The quick mounting sand and salt spreader for pickup and utility duty dump trucks.

It's two o'clock in the morning.  The phone rings. There's better than two inches of snow on the ground and more on the way.  And yesterday your were using the spreader truck to haul "stuff." You're not concerned because you know all you need to do is slip the Henderson FSP and and salt spreader into place, load up with material and be on your way.  It's quick and easy one-man operation.

Designed to fit pickups and utility duty dump trucks, the FSP meets the snow and ice control needs of a wide spectrum of users... from municipalities for intersection and spot clean-up to private contractors for malls, apartments, condos and industrial parks.  Since the FSP is a snap to mount and dismount, trucks remain available for other uses when the weather isn't inclement.

Even though the FSP is built for light duty trucks, it has a heavy duty attitude with a ruggedness built in that assures years of low-maintenance service.  Available painted in Mild Steel and 409 Stainless Steel or unpainted in 304 Stainless Steel.

Another innovative product from THE DEPENDABLE ONES.

• Single lift point on cross channel for quick, easy one-man installation.

• 10.5 horsepower I/C gasoline engine for dependability in tough spreading conditions.

• Cab-mounted controls for instant adjustment to conditions and driver comfort.

• 12-volt electric starter for instant response under all weather conditions.

• Stainless steel chute hinges for longer life and easy adjustment.

• 14" wide all steel conveyor trough for fast movement of material.

• 6-tooth cast iron sprockets for conveyor are self cleaning.  Have special collars for longer chain and sprocket life.

• Adjustable idler shaft for chain tension to assure smoother performance and longer chain life.

• 12 ga. feedgate is lever operated. Has side mounted ruler for greater accuracy of material control.

• Minimum of two (depending on model) 14 ga. side supports per side for optimum rigidity.

• All surfaces are high pressure cleaned, phosphated, primed and painted Highway Orange (304 Stainless Steel unites are unpainted).

• 12" diameter spinner disk has three 409 Stainless Steel fins for longer life

• Width of spread is adjustable form 4' to 32' to meet conditions.

FEATURES & SPECIFICATIONS

GENERAL
A self-contained utility spreader for mounting on pickups or light duty trucks and  is powered by a 10.5 H.P. I/C gasoline engine.  Material is spread by a 12" diameter spinner fed by a pintle type chain conveyor.  Material being spread is metered for accuracy and economy of spread.

Cab Mounted controls with breakaway plug for quick mounting/removal of unit.  All surfaces are high pressure cleaned and phosphated, primed, and painted Highway Orange (304 Stainless Steel units unpainted).

BODY
All electric welded 14 ga. steel sides and ends, with channel formed top edge.  Overall height is 31-1/4" and inside width of 54". Body has a single lift point on cross channel support.  The 4" x 8" 12 ga feedgate is lever operated with side mounted ruler for accurate control of material.

All units have a minimum of two 14 ga. side supports per side. 12 ga. long sills with top edge formed down to protect conveyor side chain and a 10 ga. floor with front and read rollover lips.  Bottom cross supports are 3/8" x 1-1/2" flat.

CONVEYOR
All steel, riveted, pintle chain with 1/4" x 3/4" cross bars spaced on 5" centers. Chain tensile strength is 11,000 lbs. per strand. 20:1 gearcase has a high tensile cast iron housing, aluminum bronze gear, and a hardened and ground steel worm with a 1" input shaft and 1-1/8" output shaft.

6-tooth cast iron sprockets are self-cleaning with special support collars for longer chain and sprocket life.  Sprockets are keyed to the 1-1/8" drive shaft. 1" idler shaft is counterbored with sprockets running on bronze bushings. Idler shaft is adjustable for chain tension.

SPINNER CHUTE ASSEMBLY
Material is guided from conveyor to spinner through enclosed chute with two slide rod adjustable internal deflectors. #40 nickel plated chain drives the 3/4" dia. spinner shaft which is supported by two pillow block bearings.

12" diameter spinner disc has three 409 Stainless Steel formed fins.  There are four rod and clip pin adjustable external deflectors for complete control of spread.  No tools required.  All hinges are stainless steel for extended life. Width of spread is 4' to 32'

ENGINE
10.5 horsepower 4-cycle, air-cooled I/C engine with cast iron cylinder sleeves and a Synchro-Balanced for reduced vibration.  Standard equipment includes a 12-bolt electric starter/alternator, and electric clutch that is rated at 90 ft/lbs and may be engaged/disengaged at any selected engine RPM, and a fully enclosed hinged engine hood.  The battery (not included) is enclosed within a protective casing and mounted on R. H. side of hopper

CAB CONTROLS
Completely enclosed console with rocker switches for electric throttle control, electric clutch on/off, and engine start.  The standard electric throttle control eliminates maintenance problems associated with conventional cable throttle control.

OPTIONS
 

• Premium cab control - Includes all of the standard control functions plus tachometer, hour-meter, and maintenance alarm. Functions back-lit for easier night time operation.

• Hold down kit - Includes 4 chain and binders.

• Inverted Vee - Reduces load down pressure on conveyor chain and helps prevent material compaction.

• Top grate screen - one piece (2 x #9) expanded metal screen with a angle iron frame.  Keeps larger, unwanted material out of hopper.

• H.D top grate screen - 3/8" rod x 3/8" rod with a angle iron frame

• 12" longer spinner chute - extends the spinner chute an extra 12" below mounting surface.

• 6" or 12" side extensions - for increased capacity.  Shipped loose and may either be welded or bolted to the unit.

• Urethane Spinner - 12" dia. disc with for molded fins.  Greatly extends spinner life.

• Hydraulic drive - single or dual Char-Lynn hydraulic motor(s).

• Honda engine - 11 H.P. Honda (#GXV 350) in lieu of standard Briggs & Stratton.

• 409 painted or 304 unpainted Stainless Steel - greatly extends unit life.  Sides, ends, sills, floor, feedgate, side supports, engine hood, base plate, and spinner chute assembly are all of stainless steel.

• Vehicle battery wiring harness - A two-piece, heavy duty wiring harness with disconnect plugs to hook up spreader to vehicle battery in lieu of a separate battery harness.

• Center high-mounted stop lamp kit - A sealed/housed stop lamp kit for units with side extensions that will restrict visibility of the vehicle CHMSL

• Pre-wetting system - increases effectiveness of granular material at lower temperatures.