History repeats itself...times three.  Meet the FSH-I, II and III precision spreaders.

The Legendary Henderson FSH sand and salt spreader is now available in three versions.  The FSH-I, II and III have subtle differences (see specification chart) to better meet varying specification requirements and specific customer needs.

The important features of the FSH are retained "across the board" on all three models.  The rugged dependability, precision delivery of materials to the road surface and low maintenance is ingrained in the FSH have all been retained.  It's available in a variety of sizes to exactly conform to your specifications.

So now you don't have to settle for less than a Henderson FSH Spreader... regardless of your budget.  The Henderson FSH-I, II and III...  They're what you'd expect from.. THE DEPENDABLE ONES

• Inside seams are continuously welded for extreme duty.  Sides and ends are 10 ga. and floor is 7 ga. steel.

• Top edge of hopper is a formed "J" channel for added rigidity and strength.

• Conveyor is 24" wide, all steel pintle-type chain.  The FSH-I and II have 1/4" x 1-1/2" crossbars while the FSH-III has 3/8" x 1-1/2" crossbars.  Crossbars are spaced on 4-1/2" centers.  Sprockets are cast iron and are keyed to the drive and idler shafts to prevent slippage and maintain chain alignment.

• OPTIONAL single or dual augers for reduced maintenance and smoothness of material flow

• Conveyor chain is protected by a formed 10 ga. shield in the FSH-I and II.  A replaceable bolt-in shield is standard on the FSH-III and optional on the FSH-II

• Two 5/8" stainless steel chain adjusters with 4" of adjustment provide optimum chain tension.

• Conveyor gearbox has thru-shaft for electronic control system speed sensor hook-up

• The hydraulic motor is mounted directly to the gearcase to eliminate sprockets, chains and couplers for reduced maintenance.

• The telescopic chute assembly is 10 ga. steel and is totally enclosed with two internal adjustable baffles.  Three external adjustable deflectors and one front fixed deflector with overlapping corners also contribute to precise control of material spread pattern.  A quick latching bypass chute diverts material behind the spinner chute for fast unloading.

• The 20" spinner disk is 10 ga. steel with stainless steel fins.  Polyurethane optional.

• All surfaces are high-pressure cleaned and degreased with a phosphate solution before being primed and finish painted with Highway Orange Paint

FEATURES & SPECIFICATIONS

BODY
Sides, ends and side supports are of 10 ga. steel and are continuous-seam welded from the inside.  Side slope is 45° with front slope at 18° and rear slope 9°. Floor is replaceable 7 ga. steel.  Longsills are 7 ga. steel continuous-seam welded to the sides of mild steel units.  Top edge of hopper is formed "J" channel, 1-5/8" x 3/4". Feed-gate is 10 ga. 10" x 18", screwjack adjustable from curb side.  Download pressure is reduced by an adjustable inverted vee (optional) to reduce material compaction.

CONVEYOR
Rear discharge pintle chain conveyor is 24" wide.  Chain tension adjusting rod is 5/8" stainless steel.  Idler adjustment is 4".

CONVEYOR GEARBOX
The FSH-I and FSH-II have a 50:1 or 25:1 worm gearbox with extended thru-shaft for electronic sensor mounting.  In addition, the FSH-III has a 6:1 spur gearbox available.

SPINNER CHUTE ASSEMBLY
Completely enclosed telescopic design is of 10 ga. steel.  Top-mounted hydraulic spinner motor is enclosed in the chute to maximize material flow to the spinner disk, improving spread pattern.  It is mounted directly to the spinner for elimination of shaft and bearings.  Two (2) internal baffles direct material flow onto the spinner disk directional spread control.  Three external adjustable deflectors and one front fixed deflector with overlapping corners contribute to precise control of material spread pattern.  The adjustable spinner deflectors are easily replaceable without tools for easy servicing.  A quick latching spreader bypass chute diverts material behind spinner chute for fast unloading.  Spinner disk is 20" diameter, 10 ga. steel with replaceable hub.  Six (6) 10 ga. stainless steel vanes are bolt-on and replaceable.

PAINT
All metal surfaces are high pressure cleaned with a phosphate solution to remove slag, spatter, oxide and oil residue.  The entire body is primed with a high quality catalyzed primer and then finished with Highway Orange grade enamel.  The 304 Stainless Steel units are unpainted.

OPTIONS
 

CONTROL VALVE Speed of conveyor and spinner motors is controlled by a dual pressure compensated control valve with a relief pre-set at 1500PSI. Valve has twelve (12) detent settings for each circuit and an independent on/off valve to allow start/stop without changing application rate.
SINGLE AUGER CONVEYOR Seven-inch (7") auger conveyor provides a more even flow than a standard chain conveyor with les maintenance.  A patented safety interlock feature helps prevent personal injury from the auger.
	DUAL AUGER CONVEYOR Two counter-rotating augers create a smooth spread, breaking up clumps and preventing bridging of materials.  Auger shafts utilize a polyurethane bushing at both ends of each auger to eliminate seizing and ensure ease of maintenance.
SAFETY INTERLOCK Required with optional single or dual augers. For safety, auger motors must be disabled before operator can open top grate screens.

TOP GRATE SCREENS
Hinged, 3/8" welded rod heavy duty mesh screens keep unwanted larger material out of the spreader.

FRONT IDLER AND GREASE TUBE EXTENSIONS
Grease and adjust tension on the spot.

STILL MORE OPTIONS:

• 304 Stainless Steel

• Top Grate Screens

• Inverted Vee

• Extended Front Idler Adjusters

• Extended Front Idler Grease Tubes

• 6" and 12" Side Extensions

• Hold Down Kit

• 18 HP Engine Group

• Rubber Side Spill Shields

• Roller Chain

• Cab Shield

• Spacer Bars

• Ladders

• Bumpers

• Centerline Diverter Chute

• Catwalks and Frame Mount Kit

• Side Tubes and Rear Hoses

• Short Hose Kit with Quick Couplers

• Automatic Control Systems